Manufacturer:
(Category: 308)
Automatic machine Bag machine for the production of bags on roll. Capacity 50 bags / minute (depends on the size) Machine width 1200 mm Unwinder width = 1200 mm (tubular film) Core Magazine Folding unit for C folding Floor welding and perforating unit Automatic winder (turnstile) with automatic sleeve feed
Plate press - table press - Laboratory Press - Universal Press MHSP522 Press area 230 230 mm Clear width 200 mm Manual drive with worm gear screw jacks 5 KN Pressure 5 KN (0.5 tons) Weight 55 kg Per sensor revolution 0.5 mm path, this little manual force with great force, very fine deliverable. Pressing force is long maintained by self-locking.
Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum
Data sheet heating press Oropress Pneumatic press 5 KN / 0.5 tons Press stroke 50 mm Adjustment of the clear height with handwheel and spindle, adjustable from 100 to 220 mm. With top heating plate 120 x 100 mm and temperature control, temperature up to 250 °C. Pneumatic two-hand control with triggering via Festo ZSB. Pneumatic sliding table 180 x 220 mm for loading outside the machine. Machine dimensions W = 1100 mm, L = 700 mm, H = 1850 mm Machine weight approx. 300 kg Movable on castors On request for an extra charge with second heating plate and temperature control at the bottom.
Laboratory Press EHSP125 - Demonstration Machine Table press / electric spindle press with pressing pressure 20 KN (2 tons). Press drive with screw jack, reduction ratio 1 : 12, spindle diameter 32 mm, pitch 6 mm, pressing surface approx. 100 100 mm, clear height and stroke approx. 300 mm. Gear motor 0.37 KW, 1,390 rpm, 4-pole, with spur gear i = 1 : 5, Speed 150 mm / min. Max dynamic load 20 kN. With reversible control, emergency stop and motor protection plug. Sturdy steel press frame. Base table made of high-quality aluminum profiles 4545 mm, table surface 600 600 mm, table top made of multiplex top. Total weight approx. 100 kg. The table press has 20 kN pressing pressure (dynamic load). Typical applications are pressing work with exact delivery. Suitable for pressing bonding, embossing and impressions. The screw jack has a twist protection so that the p ...
Electric spindle press REITZ EHSP100F as laboratory heating press / demonstration machine Laboratory heating press with pressing pressure 40 KN (4 tons), ratio 1 : 16, spindle diameter 45 mm, pitch 8 mm, spindle stroke 0.5 mm per revolution. Gear motor 0.75 KW, 1,500 rpm, 4-pole, with spur gear i = 1:5, Speed 150 mm / min. Max dynamic load 25 kN. With reversible control, emergency stop and motor protection plug. Total weight approx. 100 kg, table surface 600 600 mm, pressing surface approx. 150 250 mm, clear height approx. 60 mm. Base made of high-quality aluminium profiles 4545 mm, the table top is made of glued plywood top. The laboratory heating press has 40 kN pressing pressure (dynamic load). The spindle is self-locking and thus maintains the pressing force for a longer period of time. For an extra charge with heating plate, insulating plate and temperatur ...
Used pneumatic press 4 KN -Pressing force 4 KN (0.4 to) -Pneumatic cylinder make Festo -Pneumatic two-hand control - press plate made in 4 Guide pillars -Work surface between guide columns 200 220 mm -Machine table made of aluminium profiles and PA plate 600 600 60 mm -3-sided walls from Plexiglas -Total weight approx. 70 kg Suitable for stamping or embossing tools or plate bonding.
Semi-automatic drilling device for plastic parts This purely pneumatic drilling device is designed for repeatable drilling of small plastic parts up to approx. 40 x 200 x 40 mm with holes up to 3 mm. Specifications: - Linear axis travel 420 mm - Stroke approx. 30 mm - Height adjustment approx. 100 mm - With 2-hand release - Plexiglass protection on 3 sides - Emergency stop switch - Sturdy, mobile frame made of aluminium profiles - With 4 swivel castors, 2 of them with brakes - Overall dimensions approx. 1000 x 1000 x 1700 mm - Weight approx. 50 kg - With collet for drill bit 1.5 mm Expiration: - Setup: Adjust stop angle to part size - Setup: Alignment of cross table in X and Y - Setup: Set height adjustment to part height - Inserting the part - Triggering via 2-hand button and holding until drilling is completed - Removal of the finished part and placement ...
Electric surface press REITZ EHSP522 Pressing surface 200200mm Pressure 5 KN / 0.5 tons Suitable for surface bonding of plastics and composites. On request with: - Heating plate and temperature control - Load cells and gauges for use as test press ... more information
Collin Heating Press for Forming Plastics Collin Heating Press 78 Tons for Forming Plastics / Prepregs for Carbon Parts / Composites Type: Press 500 P Plate press for plastics processing / polymeric materials / ceramic masses Pressing pressure approx. 78 tons Temperature range from 20° to 300°C Usable pressing area 496 x 496 mm Voltage: 3 x 400 / 230V Y Power requirement: 3 x 125 A Frequency 50 Hz Power 67 KW Water pressure 4 bar Air pressure 4 bar Hydraulic pressure build-up, Pmax hydraulic: 160 bar Built in 1999 Weight approx. 5 tons Documentation and circuit diagrams available
Fully automatic hot stamping press Oropress Mechanical eccentric press with lift table Lift table as pneumatic sliding table 250 x 250 mm Fully automatic sequence, optionally triggered with foot switch for single stroke Heated press punch 120 x 200 mm up to 250 °C Safety grille Film Feed Unit Built in 1986
Winder: 1 coil, Brand: Aromaza, in stainless steel. With electrical panel and variator. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice. ... more information
Plastic agglomerator, engine: 75 KW (100 hp), tank size: 1 m high, 1 m diam. Electrical panel. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice. ... more information
Hydraulic shear (guillotine) Brand: Gester, Model TN-30, cutting chamber: 770x650 mm, motor: 4 KW (5.5 hp). ... more information
For sale is a laminating resin system from IMT SpraySystems. The plant is in very good condition, it has been properly shut down by personnel of the machine manufacturer and filled with mesamol for protection. New price of the system is 85000.-€. The system was cleaned and visually prepared. Circuit diagram, operating instructions and maintenance overview are available. The systems were regularly inspected by the manufacturer as part of a maintenance plan. Applications: Wind power (offshore and onshore) Shipbuilding Lightweight construction Automobile industry Railways (e.g. for the sealing of track beds) Aircraft construction (especially for the construction of the individual components) Corrosion protection Concrete renovation Chemical Resistant Equipment Wastewater (especially in the sewerage system) On request, at an additional cost, the machine can undergo factor ...
Hydraulic hydraulic filter changer. Diameter: 220 mm. Motor: 4 Kw. With head of 43 threads (spaghetti). Hydraulic group with accumulator and electrical panel. ... more information
Lot Composed of various machinery for the processing of plastic and wooden components for eyewear. n.1 Ventilation System with extractor and filters: Used for the extraction of fumes generated by the combustion of PVC materials in ovens. n.1 Cielle CNC machine: Used for milling and cutting wooden components for glasses. Brand Cielle Model ALFA 61X6, Year 2011, S/N 24/11 WEIGHT 250kg VOLT 220/240 POWER 1800W n.1 Double action oven: Used for firing PVC material (Working temperatures up to about 300 degrees Celsius, 4 pieces. n.1 Green Box Chiller for closed-loop cooling of machinery. n.1 Press and Dehumidifier (5 pieces) : o Press: Used to cut labels that were then printed on the fabric. o Dehumidifier: Used to dehumidify TPU material into granules. o 1 Laser : Used for laser cutting organic material, also used for cutting fabric (textile). Can also be used for engraving. o n ...
Trommel: 6 m x 1.25 Ø. Sheet metal bore: 50 mm, geared motor: 0.55 kw (0.75 hp) ... more information
Hydraulic filter changer: 250 mm, brand: Tecnova, double filter, for extruder 160 Ø diam, year: 2009. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice. ... more information
Film buffer silo: 10000 litres, geared motor: 2.2 KW (3 hp). With remover. ... more information