other machines for plastic used for sale

Rotor width 1000 mm Inlet 900 x 1000 mm Drive power 30 kw Engine, hydraulics, electrics completely overhauled

The main machines in the line: fluid mixer Trusioma hot and cold KO-kneader BUSS Mixing mill Buzuluk 660x2100 mm 4-roll calender Buzuluk 700x1800 mm, inverted "L" tempering and stretching device behind the calender – roller track film thickness profile measuring device winding device

REFAKT Dryer/Centrifuge/Dry Cleaner Previously used for centrifugal drying of plastic waste. Throughput capacity 300 to 1000 kg/h, depending on the type of plastic and wall thickness. Drive power 30 kw

Dryer / Centrifugal Dryer / Dry Cleaner Can be used for pre-shredded plastic waste (hard plastic, films), Throughput depending on the type of material approx. 0.5-2 t/h Drive power 30 kw

Conveyor belt / belt conveyor Belt width: approx. 300 mm Axle distance: approx. 3,130 mm Drive: 0.75 kW new - only very short in use

Conveyor belt / belt conveyor Belt width: approx. 1,400 mm Axle distance: approx. 8,000 mm Drive: 2.2 kW

There are three Concept Laser M1 3D printers available, year of construction machine 1/ 2/ 3: 2009/ 2010/ 2012, operational hours counter machine 1/ 2/ 3: 82,046/ 93,781/ 68,167h, with Laser Rofin StarFiber 200, water cooling, screening machine and documentation, at machine 1 the laser is broken and the machine is without optics, machine 2 is fully functional, machine 3 is fully functional, but a machine software error occurs regularly, which has to be fixed, afterwards production can always be continued, an inspection is possible,

Table height: 850mm, cutting width/ height: 1200/ 850mm, saw band length: 7050mm, saw band thickness: 0.5mm, weight: 500kg.

There are two identical presses available, max. stroke speed: 200mm/s, oil viscosity: 46cSt a 40°C, max. hydraulic/operating pressure: 25/ 210bar, weight of the half tool: 10t, pump power at 75/ 210bar: 200/ 70l/min, pump motor power: 30kW, weight: 25t.

A total of five Cannon foam systems are available. Materials: isocyanates and polyol, press plate dimensions X/Y: 720mm/650mm, lid opening angle: 100°, tilt angle: 60°, opening min./max.: 312mm/502mm, parallel stroke: 190mm, approach stroke: 95mm, press stroke: 95mm, ejector stroke: 75mm, control: PLC. Including material preparation. Documentation available. On-site inspection is possible.

Max. pipe diameter: 500mm, power: 1.7kW, max. pipe thickness: 6mm, weight: approx. 4100kg. Documentation available. On-site inspection is possible.

Max. pipe diameter: 400mm, power: 2.9kW, max. pipe thickness: 6mm. Documentation available. On-site inspection is possible.

Pressing force: 180kN, total stroke: 250mm, power stroke: 12mm, max. compressed air supply: 6bar.

Max. working length: 2000mm, compressed air supply: 6bar, connected load: 1200W, the machine was hardly used.

Stroke: 100mm, max. electrode distance: 230mm, electrode distance: 20kN, controls: Siemens S7-1500, with documentation, was hardly used.

Working width: 1250mm, working height: 100mm, with scoring and milling aggregate, with control cabinet, without documentation, manufacturer unknown, either Homag or Bäuerle.

Compressed air supply: 6.5bar, connected load: 2.3kW, weight: 180kg.

Compressed air supply: 6bar, connected load: 1kW, weight: 120kg, the machine has defective pneumatics.

Usable length: 3000mm, load: 50kg/m, connected load: 1.5kW, length: 3500mm, width: 550mm, weight: 208kg.

Pneumatic pressure: 8bar, connected load: 2kW, weight: 550kg, without documentation, spare parts or accessories, was maintained regularly.

Connected load: 2000W, weight: 80kg.

There are three identical machines available, including documentation.

Output: 50-300kg/h, operational hours counter: 10h, with edge trim extraction.

Loading chamber dimensions: 280x580mm, loading height: 700mm, max. load: 300kg, with protective housing and documentation, machine was functional until the end, complete maintenance would have to be carried out on the machine, inspection is possible.

There is a complete underwater pelletizing system with vibrator, heat exchanger, centrifuge, extruder, pelletizer, water basin, sieves, knife blocks, documentation and other spare parts available, a sieve changer is available separately, an inspection is possible.

There is a complete pultrusion line with three Krauss Maffei RimStar Nano pumping machines, three creels, ABUS column-mounted slewing jib crane and a KraussMaffei EW 2300 CFI winder, tensile force: 10t, max. profile dimensions: 300x50mm, max. speed: 4m/min, on-site inspection is possible.

Suitable for the production of 2D/2.5D laminate stacks from thermoset semi-finished products in the Fiber Placement process, speed: 60m/min, laying area: 1100x1400mm, with documentation, on-site inspection is possible.

Circumferential speed: 80m/s, an on-site inspection is possible.

Cooling capacity: 14.4kW, permissible min./max. temperature TS: +6°C - +20°C, refrigerant: R410A. Chilled water temperature at inlet/outlet: 15°C/10°C, ambient temperature/air inlet: 35°C. Length: 1100mm, width: 750mm, height: 1100, empty weight: approx. 220kg.

A complete Schirmer and Rotox plastic window production line is available. Production capacity: 100 windows/day, max. product dimensions X/Y: 2500mm/3500mm. 1) Processing center Schirmer BAZ 1000 G3 with steel processing, year of construction: 2010, including pre-loading magazine, measuring station, PVC G-module, EKS saw, KKF finishing station, real buffer and belt conveyor. 2) Automatic four-head machine Rotox SMH516, year of manufacture: 2015. 3) Automatic corner cleaning machine Rotox, year of manufacture: 2015. 4) Buffer and distribution system Rotox, year of manufacture: 2015. 5) Rotox sash fitting, year of manufacture: 2015. 6) Frame assembly Rotox, year of manufacture: 2015. 7) Glazing and wedding Rotox. 8) Glazing press Rotox, year of manufacture: 2012. 9) Glazing bead trolley Rotox. 10) Transom milling machine Rotox SAF 165, year of manufacture: 2013. 11) Single-head welding mac ...