used Powder Coating Equipment for sale

The curing furnace consists of a tunnel furnace in which the workpieces are baked after coating. The furnace is a straight tunnel furnace. The frame is made of steel with insulated panels. The mineral wool insulation becomes 150 mm thick in a special construction to prevent thermal bridges 1 Inner dimension length 7,000 mm Inner dimensions width 1,000 mm Inner dimensions height 2,500 mm 2 Outer dimensions incl. thermoblock, length 7,200 mm Outer dimensions incl. thermoblock, width 1,300/2,300 mm External dimensions incl. thermoblock, height 2,800 mm 3 substructure 1 set of steel profiles 80 x 80 and 40 x 80 mm 4 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5010 5 Insulation 1 set of rock wool 150mm 75 Kg/m³ 6 Ventilation system 1 set of galvanized steel sheet 7 Temperature max. 220°C 8 fans 1 pc. 7,500 m³/h 9 electric motors 1 pc  ...

Chemical pre-treatment for powder coating (3 zones) 1 Dimensions of the cabin length 3900 mm Width 1600 mm Height 2500 mm 2 dimensions of the pre-treatment complete length 4000 mm Width 3000 mm Height 4000 mm 3 Passage opening width 1000 mm Height 1700 mm The chemical pretreatment for the use of nanotechnology or phosphating consists of 3 stages in 1 spray chamber. Chemical spray pretreatment works in time and this means that the workpieces are manually pushed into the chamber. After closing the doors, the passage starts and the pumps start spraying. Each pump has different spray times. After the spraying process is finished, there is an alar ...

Chemical pre-treatment 3 zones for powder coating with spray ring (automatic) and manual Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Max. workpiece dimensions (automatic): Length: 6500 mm Width: 1000 mm Height: 2300 mm Max. workpiece dimensions (manual): Length: 6500 mm Width: 2500 mm Height: 2300 mm Tanks are positioned at ground level with a sloping floor. Tank No.1 is thermally insulated and is heated by electric heaters. Achievement: 27 kW. Volume of each tank = 1.00 m³. For degreasing (1st tank), a medium pressu ...

Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Extraction capacity: Q = 18000 m³ P = 15 kW The cab has 2 doors on one side for the insertion/outlet of the workpieces. The components are pushed into the cabin for coating via the overhead transport system. Walls, ceiling and doors are made of panels. The filters positioned on the roof absorb dust and other particles from the outside, thus ensuring clean ambient air in the cabin. The overspray during powdering in the cabin is absorbed by the extraction unit

Dimensions: Length: 7400 mm Width: 4000 mm Height: 3236 mm Extraction capacity: Q = 18000 m³/h P = 15 kW The cabin has a suction machine with filters to suck the powder from the cabin floor. The powder booth is set up in a pit to lower the entire height of the painting line. Manual doors are installed to enter the workpieces into the cabin. The overspray is extracted during powder coating via the floor. On the floor there is a grate for walking on and under the grate there is a second flat floor with automatic self-cleaning system, connected by air ducts with post-filter. A self-cleaning system automatically blows the powder from the bottom to the post-filter (suction machine) and consists of

Open Powder Spray Stand Dimensions: 2500 x 2250 x 2700 [mm] Extraction capacity: Q = 8000 m³/h P = 5.5 kW Filter: 1 stage: Filter cartridges 4 pieces à Ø 325 x 1000 [mm] 2nd stage: Pocket filter (absolute filter for fine dust) Note: The overspray during powdering is absorbed by the suction unit. The powder spray stand is delivered on rollers and is therefore mobile

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

Oven, doors single-sided, gas Dimensions: 4,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Recirculating air: Q = 12000 m³/h P = 2 x 2.2 kW Heat output: 69 kW Auxiliary heating: Gas indirectly via thermoblock

Oven, doors single-sided, electric Dimensions: 3,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 54 kW Auxiliary heating: electrically indirect via thermoblock

COMPONENTS OF THE SYSTEM Preheating oven Powder coating booth Fluidized Bed Powder Coating Lifting system Automatic Transport System – Conveyor Belt C-80 Electrical control and installation Transport and assembly Fluidized Bed Powder Coating Booth The powder is fluidized in the fluidized bed vessel when the part is preheated and positioned over the fluidized bed container. The lifting system lifts the fluidized bed tank and the part is coated. After the coating process is completed, the fluidized bed is lowered again and an air blowing system blows off the excess powder on the part. The process can be carried out fully automatically. The cab's system is designed for powder coating with powder recovery and consists of a powder chamber for powder application, a monocyclone and a post-filter for extracting powder residues Chamber dimensions Length: 2000 mm Width 1 ...

Powder coating plant (complete) with 3 zones of chemical pre-treatment and Hybird ovens (dryer and curing oven) Gas and electricity (gas or electricity also possible) The facility consists of: Chemical pre-treatment with reverse osmosis system Dryer with hybrid thermoblock Walk-in coating booth with extraction unit KG PSW 8000 Powder curing furnace with hybrid thermoblock Conveyor system with transverse displacement, manual Electric control unit Specification of production Type of workpieces varies Material of the workpieces Steel (other metals or multimetal possible on request) Maximum weight of the load carrier 200 kg System type: Manual conveyor Dimensions of the maximum workpiece in the curing furnace Max. length 3000 mm Max. width 1500 mm Max. height 1500 mm Dimensions of maximum workpiece in chemical pretreatment Max. length 3000 mm Max. width 800  ...

Powder curing furnaces in various sizes, gas or electric 1 Inner dimension length 1500 - 6,500 [mm] 2 Inner dimensions width 1700 - 1,900 [mm] 3 Inner dimensions height 2,000 [mm] 4 Steel profile substructure 5 walls Galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling rock wool 150mm 75Kg/m² 7 Floor furnace gets 2 entry rails for tray trolleys (optionally with conveyor technology) 8 Temperature 220°C 9 fans 1 - 2 pcs. 2600 - 15,000 [m³/h] 10 electric motors 1 - 2 pcs 1.1 - 6 [kW] , 1450 [rpm], 3 F, 50 [Hz] 11 Thermal power 14 - 99 [kW] 12 hinged or sliding doors on one or both sides 2 - 4 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock Stainless Steel INOX AISI 316 Heating Electric or Gas Heat-Resistant Fans and Heat-Resistant Bearings, Thermoblock Has Overheating Protection

The continuous system consists of the following components: Chemical pre-treatment by spraying Dryer Powder coating system Powder curing furnace Conveyor technology (cycle method) Electrical control Overall length: 30,000 mm Overall depth: 4,300 mm Width: 6,500 mm Workpiece weight (max.): 100 kg Temperature: 220 °C Heat output: 80,000 W Workpiece width (max.): 800 mm Workpiece height (max.): 1,200 mm Workpiece length (max.): 2,500 mm Insulating material: Mineral wool 75 kg/m³ Insulating thickness: 150 mm

Powder furnace el. or gas Powder curing furnace 6,500 x 1,900 x 2,000 mm 1 Inner dimension length 6,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 7,500 = 15,000 m³/h 10 electric motors 2 pcs 2x 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 110 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device fo ...

1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 2. Powder Coating Booth -KG DUO-01 3. Wagner powder coating plant, – Prima Sprint – 1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 1 Inner dimension length 1,500 mm 2 Inner dimensions width 1,200 mm 3 Internal dimensions height 1,750 mm 4 Outer dimensions incl. thermoblock length 2,250 mm 5 Outer dimensions incl. thermoblock width 1,815 mm 6 External dimensions incl. thermoblock height 2,006 mm, 2,296 mm incl. exhaust pipe 7 Substructure 1 set of steel profile 8 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 9 insulation walls, ceiling 1 set of rock wool 150 mm, floor is insulated with 50 mm 10 Floor Furnace Gets 2 Entry Rails for Tray Wagons 11 Temperature 220°C 12 fans 1 pc. 2,600 m³/h 13 electric motors 1 pc 1.1 kW , 1450 rpm, 3 F, 50 Hz 14 Thermal power 14 kW 15 hinged doors, single ...

1.Powder curing furnace 2,000 x 1,900 x 2,000mm 1 Inner dimension length 2,000 mm 2 Inner dimensions width 1,900 mm 3 Inner dimension height 2,000 mm 4 Outer dimensions incl. thermoblock length 2,300 mm 5 Outer dimensions incl. thermoblock width 2,300 mm 6 Outer dimensions incl. thermoblock height 2,700 mm 7 Substructure 1 set of steel profile 50 x 50 mm 8 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5005 9 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 10 floor stove gets 2 entry rails for tray wagons 11 Temperature 220°C 12 fans 1 pc. 6,000 m³/h 13 electric motors 1 pc 1.1 kW , 1450 rpm, 3 F, 50 Hz 14 Thermal output 36 kW = 30,960 kcal/hour 15 wing doors on one side 2 pcs insulated with rock wool 150mm 70Kg/m² Heating Indirectly via thermoblock Thermoblock 1 set stainless steel INOX AISI 316 heat-resistant fans and heat-resistant bea ...

Powder coating system for large parts Example:(all sizes can be changed individually) Space requirement: 30 x 15 meters Part size: L= 6,200mm W= 2,300mm H= 2,000mm Cleaning booth walk-in incl. spray wreath automatic 1 Dimensions of the cabin Length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Mass of tanks Length 1,200 mm Width 850 mm Height 1,000 mm 2 Dimensions of the cabin complete Length 9,140 mm including tanks width 5,580 mm Height 4,200 mm Coating booth walk-in, manual coating Lmmuapd8S 1 Dimensions cabin length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the cabin including extraction Length 10,125 mm Width 4,500 mm Height 3,400 mm Powder curing furnace 1 Inner dimension length 6,500 mm 2 Inner dimensions width 2,500 mm 3 Internal dimensions height 2,950 mm 4 Outer dimensions incl. thermoblock length 7,600 mm 5 Outer dimensions inc ...

.1.1. Powder Coating Booth, Open Spray Stand The overspray during powdering is absorbed by the extraction unit. The powder spray stand is delivered on rollers and is therefore mobile. - The extraction system is equipped with a 60 L powder container (rollable). - As a 1st stage, there are 4 filters in the extractor. - Above the cab is the absolute filter. 1 Dimensions of the powder stand width 2,450 mm Depth 2,350 mm Height 2,700 mm 2 fans 1 pc. 6,000 m³/h Electric motor 3.0 kW 3 Filters Φ 325x800 4 pcs Type Filter Cartridges 4 Electromagnetic Valves 2 pcs 1" "Turbo" Italy 5 absolute filters 1 pc. type pocket filter 2.1.2. Powder curing furnace Mzlxwbat 1 Inner dimension length 4,000 mm 2 Inner dimensions width 1,500 mm 3 Inner dimensions height 2,200 mm 4 Outer dimensions incl. thermoblock length 5,250 mm 5 Outer dimensions incl. thermoblock width 2,050 mm ...

Powder coating plant oven, cabin, etc. Powder Coating Booth Open Spray Stand Dimensions of powder level Width 2,000 mm Depth 2,100 mm Height 2,200 mm Fan 1 pc. 6000 m³/h Power 3 kW (electric motor) Filter 4 type filter cartridges (à ⌀325 x 600 [mm]) Electromagnetic valves 2 Pcs. 1" "Turbo" Italy Absolute filter 1 pc. type bag filter Powder Pistol Wagner "Prima Sprint" Mains Standard 230 VAC Frequency 50 – 60 Hz Input compressed air 6-8 bar Output compressed air 0.05 – 5.5 Nm³/hr. Powder curing furnace Inner dimension length 3,225 mm Inner dimension width 1,400 mm Inner dimensions height 2,000 mm Insulation rock wool 150mm [75 Kg/m³] Temperature max. 220°C Fans 1 pc. 4,500 m³/h Electric Motors 1 pc 1.5 kW, 1450 rpm, 3 F, 50 Hz Thermal power 39 kW Doors on both sides 2 pcs. Manual, insulated with rock wool 150mm 70Kg/m³ Heati ...

2.1.1. Walk-in cleaning booth, pre-treatment for steel and aluminium The cleaning booth is designed for automatic cleaning. Spraying can be done at medium pressure. There are 7 different spray tanks in the cabin. The part sizes are max. L= 6,000mm, W= 2,000mm, H= 2,300mm. 1 Dimensions of the cab length 6,500 mm Width 3,000 mm Height 3,600 mm 2 dimensions of the pre-treatment complete Length 6,600 mm Width 4,640 mm Debpm0Nom Height 4,300 mm 2.1.1.1. 1. Degreasing/Neutral Pickling Process Heated bowl, 50-55°C, time = 3-6 minutes, draining time = 80 seconds 2.1.1.2. 2. Process Acid Mineral Pickling Heated bowl, 50-55°C, time = 3-6 minutes, draining time = 80 seconds 2.1.1.3. 3. Rinsing Process 1 in this chamber rinsing is done at ambient temperature, time = 0.75-1.5 minutes, draining time = 1 minute 2.1.1.4. 4. Rinsing Process 2 in this chamber is rinsed at ambient tem ...

Powder curing furnace 4,500 x 1,900 x 2,000 mm electric 1 Inner dimension length 4,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 5,700 = 11,400 m³/h 10 electric motors 2 pcs 2x 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 74 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device for exhaust air ...

Powder curing furnace 3,500 x 1,900 x 2,000 mm gas operation 1 Inner dimension length 3,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m³/h 10 electric motors 1 pc 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal output 58 kW = 49,880 kcal/hour 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set of stainless steel INOX with heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc. stove is heated by gas burner. 15 Exhaust air 1 pc device for exhaust air pipe, m ...

Powder curing furnace 3,500 x 1,900 x 2,000 mm electric 1 Inner dimension length 3,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m³/h 10 electric motors 1 pc 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 58 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device for exhaust air pipe, manual flap ...

Powder curing furnace 2,000 x 1,900 x 2,000 mm 1 Inner dimension length 2,000 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m³/h 10 electric motors 1 pc 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal output 33 kW = 28,380 kcal/hour 12 hinged doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set of stainless steel INOX with heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is operated with gas burner 15 Exhaust air 1 pc device for exhaust air pipe, manual fla ...

Powder curing furnace 2,000 x 1,900 x 2,000 mm 1 Inner dimension length 2,000 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m³/h 10 electric motors 1 pc 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 33 kW 12 hinged doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set of stainless steel INOX with heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc oven is electrically operated 15 Exhaust air 1 pc device for exhaust air pipe, manual flap guide

Open Spray Stand 2x2,1x2,2 The overspray during powdering is absorbed by the extraction unit. The powder spray stand is delivered on rollers and is therefore mobile. - The extraction system is equipped with a 60 L powder container (rollable). - As a 1st stage, there are 4 filters in the extractor. - Above the cab is the absolute filter. 1. Dimensions of the powder stand width 2,000 mm Depth 2,100 mm Height 2,200 mm 2. Fan 1 pc. 6,000 m³/h Electric motor 3.0 kW 3. Filter Φ 325x600 4 pcs Type Filter Cartridges 4. Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5. Absolute filter 1 pc. type bag filter

Powder coating system for large parts Example:(all sizes can be changed individually) Space requirement: 30 x 15 meters Part size: L= 6,200mm W= 2,300mm H= 2,000mm Cleaning booth walk-in incl. spray wreath automatic 1 Dimensions of the cabin Length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the tanks Length 1,200 mm Width 850 mm Height 1,000 mm 2 Dimensions of the cabin complete Length 9,140 mm including tanks width 5,580 mm Height 4,200 mm Coating booth walk-in, manual coating 1 Dimensions cabin length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the cabin including extraction Length 10,125 mm Width 4,500 mm Height 3,400 mm Powder curing furnace 1 Inner dimension length 6,500 mm 2 Inner dimensions width 2,500 mm 3 Internal dimensions height 2,950 mm 4 Outer dimensions incl. thermoblock length 7,600 mm 5 Ou ...

Scope of delivery: 1. Chemical pre-treatment by spraying (in cycle process) 2. Dryer 3. Powder coating system 4. Powder curing furnace 5. Conveying technology, semi-automatic Ue3Zjkdi72 6. Electrical control Hall/ Parking space Floor area of the system max. 12,000 x 6,500 mm Industrial flooring hall floor Workpiece sizes Max. part dimensions L= 500mm, H= 1,500mm, W= 500mm Steel parts range Conveyor P&F chain conveyor in cycle method, semi-automatic Pretreatment Chemical Energy supply Electricity On-site power (max. 88 kW) Gas On-site performance Compressed Air On-Site Performance Water On-site service Calculation Type of system Cycle system Conveying speed 3.2 meters/min Length per cycle L = 1,600 mm Time for clock movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minutes Time for clock stop: Ts = 8.5-12 minutes Total time for clock Tt = Tm + Ts  ...

POLYMERISATIONSOFEN Höchsttemperatur: 220ºC NÜTZLICHE INNENABMESSUNGEN Länge : 2.500 mm Breite : 1.150 mm Höhe: 500 mm Material der Außenfläche: 1mm Karbon-Blech Material der Innenfläche: 1 mm verzinktes Stahlblech Dicke der Isolierung: 150 mm Isolierung: Steinwolle (50 kg/m³) Wärmeübertragung : Konvektion durch geschlossenen Luftkreislauf Art der Beheizung : Direkte Beheizung mit elektrischen Heizkörpern Temperaturregelung : Ein/Aus, 0-400ºC Digitaler Thermostat, Fe-Const (J-Typ) Thermoelement Umgebungstemperatur : +10ºC (während des Betriebs) Gleichmäßigkeit des Ofens: ± 2,5ºC (5ºC insgesamt) Regelgenauigkeit: ±1ºC Aufheizzeit : 25-30 Minuten, leerer Ofenzustand Ofentür : Isoliert mit Steinwolle, automatische pneumatische Guillotine-Tür Manuelle Steuerung des Öffnens/Schließens über Joystick Beschickung/Entnahme : Manuelles Einschie ...

Powder coating system, make Brennenstuhl The system consists of: 1 used hand powder spray gun, made by Brennenstuhl Type BLE 620 and high-voltage devices type BLE 620 H 1 powder sieve system, type 1500, made by Brennenstuhl 1 used powder spray booth, type BSI 2 A1 with powder recovery Connected load: 1,8 kW Compressed air req. bar - m3/h: 6 / 7,2 Clear internal dimensions: Width: 1000 mm Height: 1050 mm Depth: 850 mm

Inv. Num. : 5805 Type:- Producer: EKOL Created: 2004 Parameters: Suitable for surface treatment of aluminium profiles with maximum dimensions of 3500 x 1350 x 600 mm Annual capacity: 20-25000 m2 Heating medium: Natural gas Equipment: KOS 2 x 6 x 20 Chamber Degreasing Machine Continuous dryer Transient 2 pieces Application cabin (suction capacity 10000 m3/h) Hardening furnace (4400 x 4400 x 3700 mm) Transport Demi-Water Production Wastewater Treatment Plant

Powder furnace hybrid, electric or heated with gas burner Tray trolley for loading +/- 3°C accurate, very homogeneous air distribution References all over the DACH region, since 2010

Powder furnace hybrid, electric or heated with gas burner Tray trolley for loading +/- 3°C accurate, very homogeneous air distribution References all over the DACH region, since 2010

7 meter powder furnace with partition wall at 4+3 meter 5 rails integrated With gas burner

For workpieces up to 4m long and weighing 100kg Complete delivery, since 2010 in the DACH region Powder furnace, extraction stand for double-sided coating, upgradable with automatic coating equipment, be it Gema or Wagner POW C EQ = Powder Coating Equipment

PULVERBESCHICHTUNGSANLAGE, TRANSFER-TYP Aushärteofen - Gas, Diesel oder elektrische Quelle Pulverbeschichtungskabine - Zyklontyp oder mit Patronenfilter Pulverbeschichtungsanlage - manuelles oder automatisches System Hängefördersystem - Raupenfahrwerke und Rumpfform Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachiger Ansprechpartner in Deutschland Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. infovogamakinacom

PULVERBESCHICHTUNGSANLAGE, TRANSFER-TYP Aushärteofen - Gas, Diesel oder elektrische Quelle Pulverbeschichtungskabine - Zyklontyp oder mit Patronenfilter Pulverbeschichtungsanlage - manuelles oder automatisches System Hängefördersystem - Raupenfahrwerke und Rumpfform Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachiger Ansprechpartner in Deutschland Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. infovogamakinacom

PULVERBESCHICHTUNGSANLAGE, TRANSFER-TYP Aushärteofen - Gas, Diesel oder elektrische Quelle Pulverbeschichtungskabine - Zyklontyp oder mit Patronenfilter Pulverbeschichtungsanlage - manuelles oder automatisches System Hängefördersystem - Raupenfahrwerke und Rumpfform Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachiger Ansprechpartner in Deutschland Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. infovogamakinacom

PATRONENFILTER FÜR PULVERBESCHICHTUNGSKABINEN Die Filter bestehen aus 100% reinem Polyester. Nachstehend sind die verfügbaren Standardgrößen aufgeführt 320x600mm 320x650mm 320x1000mm 320x1200mm Andere Größen und Spezifikationen können ebenfalls angefertigt werden. Kontaktieren Sie uns für weitere Informationen und Preise. für Pulverkabinen für Staubabscheider für automatische Maschinen für Pulverbeschichtungsanlagen hoher Wirkungsgrad antistatische Option Option Bajonettanschluss POWDER COATING BOOTH CARTRIDGE FILTERS Filters made of 100% pure polyester. Available standard sizes; 320x600mm 320x650mm 320x1000mm 320x1200mm Available polyester filter media density; 160 g/m2 200 g/m2 260 g/m2 Demands of different sizes and specifications can also be manufactured.

Pulverbeschichtungsanlage für Autofelgen Kann 4 Stück 22"-Felgen in 1 Charge pulverbeschichten Komponenten der Anlage: 1,5x1x1,28m Pulverbeschichtungsofen, 18KW elektrisch VFK-2 einseitige manuelle Pulverbeschichtungskabine Förderstrecke und Ladewagen Manuelle Pulverbeschichtungsanlage Lieferung - 8 Wochen EXW Istanbul Fabrik Inklusive Montage und Schulung Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachige Kontaktperson in Deutschland verfügbar. Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. infovogamakinacom Powder coating line for car wheels Able to powder coat 4 pcs of 22" rims in 1 batch Line components: 1,5x1x1,28m powder coating oven, 18KW electrical VFK-2 single sided manual powder coating booth Conveyor track and load trolley Manual powder coating equipm ...

ELEKTRISCHER KASTENOFEN Verwendungszweck : Pulverhärtung Maximale Temperatur : 220ºC Das Heizsystem des Ofens ist als Zwangskonvektionssystem ausgelegt. Es basiert auf dem Prinzip, dass die Luft des Ofenvolumens mit Hilfe eines Umwälzgebläses in den Ofen gepumpt wird und die Ofentemperatur durch die Wärmeübertragung der Luft, die durch die Heizeinheit strömt, erhöht wird. Die Wände des Ofens und der Heizeinheit bestehen aus modularen Blechen und hochdichten Isolierplatten. Luftverteilungskanäle mit regulierbaren Klappen im Inneren des Ofens sorgen dafür, dass die Ofentemperatur an jedem Punkt gleichmäßig ist. Die Temperaturregelung ist digital und ermöglicht eine präzise Einstellung der Ofentemperatur. Die Heizeinheit wird seitlich, hinten oder oben am Ofen angebracht und besteht aus einer isolierten Heizkammer, einer Heizzelle mit Widerstand im Inneren, eine ...

Gema, Wagner COST-EFFECTIVE AND VERY LONG LIFE POWDER GUN CASCADES FOR ALL WELL-KNOWN POWDER COATING GUNS MADE IN TURKEY

PATRONENFILTER FÜR PULVERBESCHICHTUNGSKABINEN Die Filter bestehen aus 100% reinem Polyester. Nachstehend sind die verfügbaren Standardgrößen aufgeführt 320x600mm 320x650mm 320x1000mm 320x1200mm Andere Größen und Spezifikationen können ebenfalls angefertigt werden. Kontaktieren Sie uns für weitere Informationen und Preise. für Pulverkabinen für Staubabscheider für automatische Maschinen für Pulverbeschichtungsanlagen hoher Wirkungsgrad antistatische Option Option Bajonettanschluss POWDER COATING BOOTH CARTRIDGE FILTERS Filters made of 100% pure polyester. Below are the standard sizes available 320x600mm 320x650mm 320x1000mm 320x1200mm Demands of different sizes and specifications can also be produced Contact us for more information and price. abcs://vogamachine.com for powder booths for dust collectors for automatic m ...

Powder coating line for car wheels Able to powder coat 4 pcs of 22" rims in 1 batch Line components: 1,5x1x1,28m powder coating oven, 18KW electrical VFK-2 single sided manual powder coating booth Conveyor track and load trolley Manual powder coating equipment Delivery - 8 weeks EXW Istanbul Factory Assembly and training included

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

POWDER COATING HAND GUN Cost effective and long life cascade Made in Turkey

POWDER COATING LAB HAND GUN

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

2. VFDK-3 WALL TYPE CARTRIDGE FILTERED POWDER COATING BOOTH Wall-type powder coating booths are an economical manual powder coating booth solution for companies producing and powder coating small parts. These powder coating booths save space in the workshop and are a practical method of powder coating the work pieces to be painted. The wall-type coating booths can be combined with conveyors in transfer-type powder coating plants or have a simple conveyor line according to the project. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists o ...