used Rubber extruders for sale

Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m

Refer to code 1043 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1042 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

screw ø:: 60 mmscrew length:: 11D screw speedl:: -- U/mindrive power:: 18,5 kWCondition: used, overhauledSpecification: rubber extruder - used- screw diameter: 60 mm- screw length: 11D- screw length: approx. 660 mm- overhaul of screw and barrel- Overhaul of feed roller and safety cage- New rotary union for water- AC motor: 18.5 kW- New control cabinet with frequency converter for variable speed- New cabling- Pressure and temperature sensors on the extruder head- Safety device- CE marking and an operating and maintenance manual in EnglishOverhauled according to CE-Standard safety regulationsWarranty: 1 yearOption:3x temperature control units up to 95°C water temperature Power: 6 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Refer to code 1046 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Barwell C3 Preformer Extruder 2500 psi Output 600kg/hour Ram type Extruder Extruder size 250mm With Rotary Cutter 8 fixed speeds Year 1980

Extruding height 1010 mm, Mailefer screw,

available Berstotff Rollerhead - Extruder Cold Feed Extruder - 200mm x 218D 2 roll calendars 400mm x 1200mm see attached description!

Pin-Convert-Extruder, GE 120 SC, make Berstorff, cold lined

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

Francis Shaw 30mm Extruder Roller Feed LD ratio 15:1 Year 1993

Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

screw ø:: 90 mmscrew length:: 20D screw speedl:: 0 - 60 U/minCondition: NEW,Specification: Rubber vacuum extruder - with warranty- Screw diameter: 90 mm- Screw length: L = 20 D (approx. 1,800 mm conveying length)- Screw speed: 0 - 60 rpm- Centre height of extruder: approx. 1,125 mm incl. base frame- Max. permissible injection pressure: 500 bar- with feed roller- Extruder water-tempered- Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump- Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm- Vacuum cylinder: three tempering zones BL = 1,057 mm- End cylinder: one temperature control zone  ...

Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009

Berstorff 8inch (200mm) Cold Feed Pin Extruder Manufactured by: Krauss Maffei Berstorff Extruder Type: Vac GE 200 SC, Pin Type No of Pins: 2 X10 + 1X12 (Hydraulic adjustment) Screw Diameter: 8"/200 mm L/D ratio 18:1 Drive: 300 Kw, 1500 RPM Screw speed: 33pm Complete with Control Panel Roller Die Suitable for rubber compounds Year 2009

Refer to code 1045 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Refer to code 1044 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

L/D=20.7 External dimensions 2700×1000×1400(LxWxH) Screw stiffness HRC65-68 Screw diameter 90mm Engine power 30KW/1470rpm SCREW LENGTH 1860 mm Heating section number/power 6kw×2

Profile extruder, GE 90 x 16 D vacuum, make Troester, cold lined

Screw with vacuum zone, output approx. 255 - 400 kg/h, straight head

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

screw ø:: für Extruder 90 mmscrew length:: -- screw speedl:: -- U/mindrive power:: 13,6 kWCondition: little used, as good as newSpecification: gear pump ZP 75/50 for extruder size 90- SEW helical gear units: R 97- Siemens direct current motor: 1 GG5 118- Drive power: 13.6 kW, 57 A- curved tooth coupling- With clamp for the head connection,- Clamping flange for extruder and head connection,- Base plate with linear guide rails,- Tooth shaft diameter: 75 mm- tooth width: 50 mm- helical gearing, hardened steel bearings, right-hand drive- without controlThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

8" Cold Feed Rubber Extruder

screw ø:: 120 mmscrew length:: 17D screw speedl:: 42 U/mindrive power:: 138 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.